Thanks for the input. Yeah, my research has been more linux specific. My feeling was that Intel would perform well under linux, but browsing around most of what I’ve been finding are posts from a year ago, and nothing more current. I’m assuming that the cards (and more specifically driver support) would only get better in time (assuming it’s not the next optane… haha).

Yeah, I love the Hyve Zeus servers. I currently have three making up my proxmox cluster. They are great so long as you have another system for storage, as they only fit 2x 2.5" drives otherwise. I have my cluster linked to an SSD pool on trunas via 10gb for all my vm’s.

As for the GPU - Yeah, it’s too long because of the cooler. It’s possible I could get an alternative cooler, and it’s something I could look at. Although the server I bought for it has already been sent back since the gpu didn’t fit.

The NUC isn’t a bad idea, but I got a good deal on the P2000 and was hoping to utilize that. I recently started hosting plex for my in-laws, and want to get our daughter setup with an account with her going off to college. My current plex setup works fine, but as I’m adding people accessing it remotely, I just figured it would be nice to put the P2000 into play.

Omg… I’m a dummy. Thank you, stranger!

OK… I guess I’m an idiot… Where is the pre-reg on the playstore?

My first printer was a creality cr6 (kickstarter edition), and it’s been absolutely fantastic. I use my printer to solve problems mostly by designing my own parts for things. My printers really are tools to me. My cr6 doesn’t get used a lot, but I turn it on, run the auto level, and hit print. I’ve printed roughly 2000 hours with it, and I’ve had one jam, and zero failed prints (I’ve stopped a couple for various reasons, but I’ve never walked in to find a spaghetti mess). I upgraded to the community firmware, a dual drive extruder, and capricorn. Also, I print almost exclusively in PLA.

My second printer is a kingroon kp3s. I’ve printed very few parts with it. I got it as a toy, and plan to install klipper and just be able to print fast. I like the small for factor, direct drive, and linear rails. It’s a decent printer, but it’s not as “easy” as my cr6 (no ABL, and my bed seems to have a high spot right in the middle). The prints I’ve printed for testing are small, and the quality has been really good. I just haven’t had a lot of time to play with it and really dial it in.

All this said… I’d by a mk4 in a split second for my use case. Again, as a tool that I turn on every few months, prusa is a known workhorse. My only complaint with my cr6 is it’s slow… And the mk4 would take care of that.

I echo these exact thought, except it was sync for me. Without question the most used app, always first to be installed a new phone, and had the designated spot on the home screen.

Makes me sad where things are going.

I’m currently running pfsense, and then mikrotik and ubiquiti switched and ubiquiti AP’s. I’m slowly removing the ubiquiti switches and moving to mikrotik as I’m upgrading to 10gbe. Mikrotik switches have a reputation of being reliable, capable, and cheap-ish. So far I like them. While I love ubiquiti’s single pane of glass approach with the unifi controller, I wanted to get away from that a bit. I work in IT, and most things I encounter don’t have that… And are configured via cli and or web interface. When I built my home network I jumped into ubiquiti for the ease. Now I’m back tracking for more learning.

Thank you to the dev’s as always!! I’ve updated one node so far, and it went flawlessly! Two to go! Keep up the great work, devs!

Thank you, friend! 👍

Pay walled.

At that depth, I feel like creaking and cracking is probably common. However, I don’t think there would be any spraying as an indicator. Based on this tweet I saw earlier.

Incase anyone is wondering… Little clip of an implosion

RIP to those who parished. I think most can take solace knowing that if it turns out to be true that it was an implosion, it would have been instant, and the occupants likely felt nothing. .

Yeah… Unreal. Crazy to think you could have resurfaced… But still suffocate to death.

I think it’s as equally important to remember; A backup is not back up… Until you’ve restored from it.

Test your backups, folks.

I am ALL for this!! I was a sync pro user for years!! Miss that app now that I’m done with reddit.

• Radarr
• Sonarr
• Lidarr
• Prowlarr
• Plex
• Pihole
• Papermerge
• Syncthing
• Guacamole
• Klipper
• Octoprint

There’s probably others. Just a quick off the top of my head list.