Yep, YouTube even has an A/B testing tool for automating this.
Yep, YouTube even has an A/B testing tool for automating this.
Not necessarily without concern. Some containers have startup scripts that chown or chmod all files in some locations. It can mess up access for other containers if shared.
First will be shared files between the container in a single named volume. The others will create 2 named volumes pointing at different files with example1 from the 3rd not being on NFS.
It depends on how the router responds to other non-forwarded ports. For UDP an open port with no response is the same as a dropped packet. A scanner will only know if the device sends an ICMP response back to indicate that it is closed.
It’s not well explained for sure but judging by the names of the cookies I bet those store the consent (opt in/out) values for the other tracking options. Another way of putting it would be those are functional cookies related to the cookie consent form itself so that you don’t have to re-select consent options every time you visit the site.
From what I’ve read is not authentication bypass, it’s a RCE using certificates to deliver the payload. If a specific signature is found it runs the code that was sent in place of the signing public key. It also means that only someone who has the ability to generate that specific key signature could use the RCE.
There were some other bits that looked like they could have been placed to enable compromising other build systems in the future when they checked for xz support.
If filesystem UUIDs are IP equivalents. Then device paths are MAC addresses. FS labels are DNS. Device mapper entries are service discovery.
The biggest issue is that your corners are lifting from the bed during the print. Fixing this is usually a combination of making sure the bed is clean and adding a brim to increase adhesion. Maybe messing with temperature and cooling fan settings for the first few layers.
Second is things look a bit over extruded. This could just be due to the corner issue though so fix that before any other changes.
The reasoning is that it is not illegal to fake most student ID cards but it is a federal offense to fake or alter government issued ID documents.
That way if it becomes an issue they can just pass it on to the authorities as their problem.
“Invalid” or “unparseable” are more understandable descriptors in normal language. I don’t think I ever heard of garbage/junk being used for that in language theory but it may be domain specific usage.
There are a lot of edge case characters around visually indistinguishable names. If that is a concern usernames should use a restricted known character sets instead of trying to block specific characters. You likely should also treat lookalike characters as equivalents when checking for username overlap.
As someone who also has produced code that looks like random characters spewed onto a terminal while using fpdf, I feel this one.
It can still have issues with potential attacks that would redirect your client to a system outside of the VPN. It would prevent MitM but not complete replacement.
Likely you needed to include the intermediate cert chain. Let’s encrypt sets that up automatically so it’s quite a bit easier to get right.
Fridges with a dial usually are an uncalibrated simple analog thermostat sensor (often a gas tube with a pressure switch) along with a simple analog control board. Fridges with a digital thermostat tend to use a calibrated sensor (usually a thermocouple) with a digital control board.
You might also try running a few leveling probes in a row to check the repeatability of the measurements. It’s possible that something is messing with the ability to make good measurements (unstable power feed, heat warp, probe binding, etc).
Yeah, I think that was it. I also played a heck of a lot of sudoku on it.
That’s awesome, I had an iRiver as well. Ended up putting custom firmware on it after a bit as the original firmware was buggy at times and lacked features. The device itself was surprisingly capable and could even play video.
I had that very device right about 2002. Put my whole CD collection on a few mp3 disks. Replaced it a few years later with a 6GB mp3 player.
It looks like underextrusion at speed. It might be a clog or you might want to try a higher hotend temperature. PLA can have inconsistent ideal temperatures even with the same brand due to different colors and additives between batches and 185 is on the low side.