Air conditioners are not the best for the planet long term, but Europeans may need to care a bit more about themselves in the short term and start installing more of them.
The insulation requirements in the US are higher than many European areas with similar climates. Germany for instance would fall in region 4 and 5 of the US climate wise. R-30 is required for walls, R60 for ceilings, and R20 for floors for homes in the US. Germany recommends 6cm of wall insulation ~R8, 14cm for ceiling ~R19, and 6cm for the floor R8.___
…and we don’t really have recommendations as such. KfW55 is nowadays mandatory for new construction, KfW70 and up gets you cheap loans. KfW70 means less than 45 kWh/m² per year for heating and they don’t really care how you achieve that. We didn’t really get around yet factoring cooling into stuff.
I was using freedom units for both. The R values were determined based on insulation thickness. Because you Europeans use energy consumption for your requirements it’s impossible to compare with US requirements. I did find this table giving recommendations for insulation.
Your numbers still don’t make any sense or are a century out of date or something.
The KfW also hands out loans to add insulation to existing buildings, U0.14 roof, 0.2 walls, 0.25 floor, so lowest R22.7 in Rankine land. The other numbers are for window, listed buildings, etc. All of that is minimum what’s actually recommended is well ask your architect and budget. There’s only so much that’s sensible to do when it comes to old construction as at some point hunting for air gaps and heat bridges is more bother than tearing the thing down and building new, and the KfW did set the standards sufficiently low so that currently uninsulated buildings at least get something and you can’t just tack on half a metre of insulation to an existing structure either. Mostly it’s the roof that’s missing insulation, walls tend to be defensible as they are and it probably makes more sense to upgrade the heating system.
You can back out R values based on insulation thickness, that table may be old… It didn’t have a date on it.
The values you provided equate to freedom R values of R40.5, R28, and R22.5 for the roof, walls, and floor. Those are inline or behind the US minimum requirements R60, R30, R20.
The insulation requirements in the US are higher than many European areas with similar climates. Germany for instance would fall in region 4 and 5 of the US climate wise. R-30 is required for walls, R60 for ceilings, and R20 for floors for homes in the US. Germany recommends 6cm of wall insulation ~R8, 14cm for ceiling ~R19, and 6cm for the floor R8.
___You know if you muppets used sane units you’d be right. But you’re using colonial measurements.
Here’s conversion table. US R30 is equivalent to proper units R5.3, R60 is R10.5.
…and we don’t really have recommendations as such. KfW55 is nowadays mandatory for new construction, KfW70 and up gets you cheap loans. KfW70 means less than 45 kWh/m² per year for heating and they don’t really care how you achieve that. We didn’t really get around yet factoring cooling into stuff.
I was using freedom units for both. The R values were determined based on insulation thickness. Because you Europeans use energy consumption for your requirements it’s impossible to compare with US requirements. I did find this table giving recommendations for insulation.
https://www.new-learn.info/packages/clear/thermal/buildings/building_fabric/properties/insulation/images/slide4.gif
Your numbers still don’t make any sense or are a century out of date or something.
The KfW also hands out loans to add insulation to existing buildings, U0.14 roof, 0.2 walls, 0.25 floor, so lowest R22.7 in Rankine land. The other numbers are for window, listed buildings, etc. All of that is minimum what’s actually recommended is well ask your architect and budget. There’s only so much that’s sensible to do when it comes to old construction as at some point hunting for air gaps and heat bridges is more bother than tearing the thing down and building new, and the KfW did set the standards sufficiently low so that currently uninsulated buildings at least get something and you can’t just tack on half a metre of insulation to an existing structure either. Mostly it’s the roof that’s missing insulation, walls tend to be defensible as they are and it probably makes more sense to upgrade the heating system.
You can back out R values based on insulation thickness, that table may be old… It didn’t have a date on it.
The values you provided equate to freedom R values of R40.5, R28, and R22.5 for the roof, walls, and floor. Those are inline or behind the US minimum requirements R60, R30, R20.