I have an eight-year-old laptop that needs replacing and I’m paralyzed. What are the most reliable ones now? Do I need a desktop for CAD? Pros and cons of operating systems (and where do I find them?) Browsers ditto? Where do I find answers that aren’t just product marketing?
Desktops have a lot more bang-per-buck than laptops, and are significantly more repairable/upgradable. Laptops make a lot of compromises to squeeze everything into a portable form-factor that runs on batteries. However, only you can say whether that outweighs the space/portability benefits of a laptop, for your use-case.
I’m a sysadmin, I work with Linux every single day, and I say to you: do not go Linux. It isn’t designed for what you want it for; it’s somewhere between the hobbyist/industrial spaces, whereas you want and need something consumer-focused. Get a nice straightforward Windows box.
Macs are also decent, though they’re even more bucks-per-bang than laptops, and there aren’t mac versions of every application; you’d need to check what’s out there.
Operating systems come with the computer if you’re buying them retail; you can buy them separately if you’re building from parts. Linux is free to download.
Laptops can be ergonomics hell; tiny keyboards, little screens right at desk level - if you’re working at them all day, a proper monitor and keyboard are de rigeur - at which point, you may as well have a desktop, unless you need to take your computer with you when you go places.
Brands, ehh. HP and Dell are decent, but whatever. Or if you’re a getting a desktop, you could build your own and save a packet, but that’s a whole other rabbit hole of complexity to dive into.
You need SSD, not HDD. HDD is slow as hell, physically fragile, makes annoying grunting noises… just don’t even consider it. SSD is unbelievably faster and better in every respect. A little more expensive, but worth every penny. Don’t go less than 500GB, preferably 1TB.
RAM, you need 16GB at the bare minimum; consider 32GB.
Monitors: preferably 27", at least 1920x1080, consider 2560x1440 or even 4k. You don’t need high refresh rate, you do want an IPS-type panel. Having two monitors will greatly improve your quality of life, if you can swing it.
CPU: there’s a million and thirty different ones out there. Just get something released in the last couple of years, you’ll be fine in most cases. There’s usually a shoulder in the price-performance curve about 75% of the way up the rankings; that’s the optimal place to buy if you want something that will keep you going a good while without getting ridiculous.
My god, thank you!
His advice is fantastic but I have to mention 1 thing… HP is TERRIBLE. I’m a repair technician and we get so many of these damn things, it’s like 10% to 20% of our business, and we repair iPhones, androids, iPads, Mac’s, PC desktops, laptops, gaming PCs and even vintage computers.
This is because of how HP laptops are designed. All of the components and hinge assembly are attached to this thin flimsy plastic palm rest, it has the rigidity of a wet newspaper. During use, opening and closing, the plastic flexes constantly and over time the plastic gives, snaps and the laptop can no longer stay open.
Not only do they break frequently but the repair is expensive. Since everything is attached to the palm rest a technician needs to gut, then reinstall every component onto a new palm rest. Around 1-2 hours. Troubleshooting and testing afterwards also takes longer, as every component has been “fooled around with” there’s a high likelihood for mistakes.
It stings when I have to tell customers that the repair for their $500 laptop is like 250 or 300$.
Oh: if you’re doing fancy-schmancy 3d industrial CAD stuff for designing car engines or the like, you’d want to make sure you have a nice GPU, which is typically in the ‘gaming laptop’ category if you’re going laptop.
However if you’re just doing ordinary diagrams and stuff, then onboard video will be absolutely fine.
Desktop vs laptop doesn’t matter much for any given CAD software. Just make sure you hit the recommend specs of whatever software you’re looking to use.
The bigger thing will be if whatever CAD software that is is Windows exclusive or not. I’d check that before deciding to go the Linux route (which most people on here are going to try to steer you towards.)
Good point!
I’ll say as a cad professional, the linux space was abandoned by the largest companies a while ago. Unless you go browser based (onshape) your software will either be less mature (Freecad, solvespace) or straightup script based (openscad).
Or you will have to use a dedicated VM but IMHO it’s not worth it when you can just dual-boot.
Desktop vs laptop doesn’t matter much for any given CAD software. Just make sure you hit the recommended specs.
There’s truth in this, but also caveats. I work with a bunch of mechanical engineers. In the warmer months, while working on really complex drawings, they need to take frequent breaks.
It’s because laptops are designed to be compact, by sacrificing airflow. So when they run anything heavy, the CPU would heat up and start throttling itself.
On a desktop, easily solved by slapping on a semi-decent cheap cooler. On laptops, well, you take frequent breaks.
you could get round this a bit by going for laptops that are designed to be used under load for extended periods of time… like gaming laptops.
Despite the good specs i wouldn’t want to be doing much heavy computing on a thin and light
Nah nah nah nah just make em all draw in the walk in.
If the CAD package can leverage GPU computing, then an eGPU is a good compromise. That way you can have plenty of power and airflow at the desk for intensive tasks, but you don’t need to lug all the hardware to the floor for interfacing with plc’s or to meetings. Although systems with good eGPU support are often expensive enough that keeping a separate desktop workstation and a lightweight laptop is competitive.
High single core cpu clock speeds and lots of ram should be the first priority for cad. Solidworks, for example, does not handle running out of ram gracefully at all.
Lots of good info on laptops here without all the marketing junk: https://www.rtings.com/laptop/reviews/best
Get Windows 11 Pro (not Home), so you have more options for turning off annoying crap built-in to Windows.
For CAD get at least 16GB of RAM, but I’d recommend 32 or 64.
Mouse reviews: https://www.rtings.com/mouse
CAD would benefit from a larger monitor than a laptop can have: https://www.rtings.com/monitor
If you do consider Linux, check out https://system76.com/ — If you get one of their computers, Linux (Pop!_OS) comes pre installed, is supported by this company, and would be pretty similar to using Windows or MacOS.
Thanks, you gave me lots of good resources here!
Lots of great recommendations here. I’ll add some things:
- Windows will be a great choice for something you are familiar with, but the current iterations are definitely heading in the direction of being advertising-filled messes. So it’s not a bad idea to look at alternatives.
- Apple should be a good choice for a “just works” system without a lot of junk in it. But if you’re new to it there will be a learning curve. Software options are also more limited. AutoCAD looks to be your only major commercial CAD option there.
- If you want to explore Linux, try a live usb stick and see what you think. It will feel very different and there will be a larger learning curve, but a liveUSB should be a risk free and relatively easy way to try it out and see if you love the difference or hate the change. If you still are interested at that point consider dual-booting or repurposing an older system for something to tinker with.
- CAD in particular might be a sticking point. Windows will give you the most options. You didn’t mention whether you’re tied to a specific system as is common for a profession / livelihood or whether you’re open to options. If you’re able to look at alternatives— AutoCAD is on Mac and Windows, SolidWorks is on windows only. QCAD is a smaller option for 2D CAD on all three platforms and I’ve been happy with it for everything I’ve tried to do.
Thank you for your input! I’m hoping to do some 3D work, but I have the same view as you of Windows’ future. I will have to determine what I can live with: ads in the OS or 2D CAD.
Framework is the laptop designed intentionally to be fixed. They just came out with a big size version with a dedicated GPU since you mentioned CAD.
You don’t need a desktop for CAD anymore.
If it’s your livelihood then stick with Windows. If you need a little reliability then Ubuntu will have the most support. Otherwise, pick your flavor of Linux that you like most.
Browsers are chromium v Firefox. They will both get the job done. Chrome (google version of chromium) plays nicest with your google account.
As for answers, unfortunately you have to hit up multiple sources for any question. Usually ask a pc magazine, YouTube, and Reddit/Lenny and compare the answers while remembering their base motivations for providing answer.
You don’t need a desktop for CAD anymore.
Not for the raw processing power, but anyone doing serious CAD work is going to want at least a 21" monitor, relying on just the laptop screen is going to be difficult especially (and I speak as someone aged over 50 myself) as your eyes become less able to focus on fine details as you get older.
So OP needs to decide if they’re going to want to use the machine for other things as well, in which case a laptop + external monitor might be fine, or if it’s a dedicated work/hobby CAD machine in which case why not get the desktop + monitor.
Good points!
I’m on a 7 year old laptop, i7-7500U CPU, 32gb RAM and run Solidworks in a VM as I’m also running Linux.
It handles parts fine, but struggles a bit with very large assemblies and rendering on surfaces. This I assume is the lack of dedicated GPU.
There’s many aspects of Solidworks that are CPU-bound. Worse, they’re only utilising a single core. It’s ridiculous for 2024.
I’m on a rather old version of Solidworks, for various reasons, but had hoped for some improvement by now.
Although, I’m not surprised. Many, if not all of the ‘premium’ CAD and CAM software I have used have no multi-threading either.
If you’re looking at new laptops, there’s two main things to look out for IMO: soldered on RAM, and a plastic chassis.
Over the years I’ve had the unfortunate experience of repairing so many broken HP laptops in particular that I just avoid them out of principle. They tend to place a lot of heat generating components internally right beside the lid hinge, causing the plastic there to weaken and start to break off. On some occasions I’ve seen this plastic get stuck inside the nearby CPU fan, which causes the laptop to overheat and shut down on you without warning.
There are other companies that used to be more sensible with their component placement, like Asus and Fujitsu, but IMO it would be relatively safe to pick a laptop with a non-plastic chassis that feels good to use.
No, a desktop is not mandatory for CAD. I personally use both a 4 yo desktop and a 12 yo laptop just fine
Everyone else has posted some really helpful answers for your other questions so I’ll end my post here!
Good tip on the plastic chassis, thanks!
What you need for CAD is a mouse; trackpads are just too fiddly and imprecise. I use a Logitech MX Master, which works great over Bluetooth to a laptop.
I’ve had my MX Master for about 4 years now, best mouse I’ve owned. Tracks on almost every surface, easy enough to open and replace the internal battery, and feels great in the hand. The dual friction scroll wheel is amazing for scrolling through large webpages, folders, and lines of code.
Really wish it was at least a bit open source though. It’s capable of so much with the extra built in buttons and additional scroll wheel, but outside of Windows and Mac they are not very programmable
There is https://github.com/libratbag/piper for Linux which seems to support the my master. It is definitely more limited than Logitech gaming software, but allows me to configure my g600 just fine.
A number of posts have mentioned brands, but it’s very important to consider the line within the brand. Consumer-oriented lines from HP (Pavilion, Essential), Dell (Inspiron, Vostro), and Lenovo (Idea pad, Legion) are absolutely terrible. Plastic everything, difficult/impossible repairs, no upgrades, etc. Every corner that can be cut, has.
Instead, look to the enterprise lines. Lenovo Thinkpad (my preference)/Think centre, Dell Latitude/Precision, HP Elitebook. I usually find the older ones (3-5 years old) that are off-least after enterprises are done with them, do a minor upgrade, and I’m good to go for a long time. Obviously that will depend on your needs, skill set, and desires.
Even Lenovo dropped the ball on their latest Thinkpads. Terrible thermal design, they messed up their BIOS (long boot times, Lenovo support just told my colleague to roll back to an older version, lol. Then the next support call they wouldn’t give support because he wasn’t on the newest version). Overall total bullshit for fully decked out $3000 machines.
Personally I’d never buy a laptop if I can avoid it, desktop parts are just so much better and cost less.
1st thing I’d do is set your requirements. What are you using this laptop for? Do you need to run specific software for it? What does that software need to run well. You mentioned CAD, I had a look at the System Requirements for AutoCAD and most of this is very easy to pick out on a spec sheet and as long as you’re not picking the cheapest machine you should be fine. The only specifically weird one is the bandwidth requirement for the GPU, but pretty much any chip less than 5 years old should be fine. You can search the model on wikipedia for the bandwidth figures.
As for the whole laptop vs desktop debate, laptops give you portability, whereas a desktop is more erganomic; a laptop can be taken anywhere and as long as you’re not using super power hungry parts you should be able to get a few hours out of it without needing mains power. A desktop allows you to place the keyboard, mouse, and screen in a way which is more comfortable for you, but you can’t move it.
Either way, you need to set some minimum specs. I’d say 1920x1080 screen (also known as full HD), 16GB RAM, SSD storage.
For buying a laptop, avoid Apple. Their reliability has gone down the drain over the last 10 years with each model having a reliability issue. (butterfly keyboards, dust ingress into screens, STORING THE BIOS IN NAND) and that’s before the overpriced RAM cost. Used business laptops are a good deal and can be repaired fairly easily. If you’re feeling up to it, many of them can have their RAM upgraded with only a screwdriver. For specific processors, look for Intel Core i3/i5/i7 12th gen or 13th gen or the Intel Core Ultra 5/7 for the newest parts, just check that the processor model number ends in a ‘U’. This means it’s not going to eat your battery in less than an hour. For AMD, look for model numbers in this format ‘7x40U’ where the x is either an 8,6,5, or 4. These use AMD’s latest technology, are more power efficient than Intel and give excellent performance.
For a desktop, don’t by from a big brand. HP, Lenovo, Dell and Acer all use proprietary parts which makes fixing these machines impossible and that is only the start of the issues. Smaller builders will use off the shelf parts which can be replaced and upgraded easily. Cyberpower PC has a fairly cheap PC which should run everything even if it’s a bit old and ugly here. Just remember, you need a screen, desk and chair.
Choosing a web browser is just an illusion of choice. Almost every browser is based on Chrome (included Microsoft Edge) with Safari merely being a cousin of Chrome ( Chrome’s browser engine Blink is a fork of Apple’s WebKit used on Safari). The only exception is Firefox which uses it’s own. Firefox is pretty good, it’s no slower than Chrome and has better extension integrations (no Manifest V3 shennanigans) just make sure you install uBlock Origin.
You’d pretty much be stuck with Windows 11 as an Operating System which is shite. Unless you’re willing to have your phone open looking up how to bypass the Microsoft Account requirement and then spend an hour fixing Microsoft’s stupid default settings, you’ll have to put up with it and all it’s awfulness. But there isn’t any othe choice, Linux is a pain to setup unless you know what you’re doing (I use Arch, I don’t recommend any distro for casual use) and will likely not support any CAD programs.
Awesome, this is so helpful! I am somewhat crushed that I can’t practically escape Windows 11, that was a big goal for me.
You mentioned CAD, I had a look at the System Requirements for AutoCAD and most of this
Keep in mind that AutoCAD is only 2D and many of the core controls are different from what you’d normally find due to Autodesk trying to cater to people who started using it in the 90’s. AutoCAD’s requirements are going to be different from modern packages like NX or Solidworks
CAD works fine on windows laptops. Look for sales at microcenter and get something with a dedicated video card. Set a budget like $1000 and start there.
found the Canadian. Lol
How complex are the things you’re looking at modeling in CAD? I bought a used Dell Latitude 7400 with an i5 to putter around on when I don’t want to sit in front of my fixed position tower. It’s truly not a very impressive device from a specifications perspective, but it runs fusion 360 well enough for basic CAD work (single, non-complex components). Fusion 360 has given me warnings about the computer specs, but I haven’t run into any performance issues.
You’ll want an external mouse, but that’s not a big deal.
I haven’t tried loading a larger model on it though. I suspect it would work, but it would struggle a bit more.
If you’re going to get a laptop, I suggest buying an “enterprise” model. They’re generally better built than the consumer models.
I honestly don’t know. Some architectural stuff (ie a porch) and smaller mechanical assemblies (toys).
I’ll give you some general advice and am happy to answer any follow up questions you might have.
Upfront, I recommend getting a laptop from a well known vendor running Windows. If you aren’t looking to go on a technology learning expedition, just need something that will work, and will have a warranty and a support line if things go wrong, you can’t beat a vendor. Dell is probably where I would look, but Microsoft surface, and Thinkpad’s are also good.
Going with Windows from a vendor supplied laptop will maximize the amount of support you have and the number of things that just work.
If you are looking for more of a technology project, I’d need to know more about what your tolerance is for fiddling with technology or your computer not working.
As for CAD, as others said, check the recommended software specs and match your computer to them. Make sure you give yourself plenty of fast storage like m.2.
For browsers, I use Firefox. I’d recommend Firefox as being a good balance between privacy and just working with plugin support. But chrome and other chromium based browsers like edge also just work.
Consider getting a Microsoft 365 personal or family account. For $100/year you get cloud storage, computer backups, and the local and online office suite, and it all integrates well into Windows.
If any of the above assumptions are wrong, I’m happy to update recommendations.
Finally, how do you learn to fish? It takes time to come up to speed on things, so slowly learning, finding neutral review sites like maybe Tom’s hardware, and doing your own testing.
Lots of people will give you opinionated advice, so don’t be afraid to be skeptical. Think about what’s important to you, whether that be just working, or privacy, or availability of support materials.
Right now I’m skeptical of anyone who is trying to sell me something. Thanks for mentioning Tom’s Hardware, I’ll take a look at them. One of my concerns is privacy, and I’d rather not store things on the cloud. Of course, maybe it’s too late for privacy, but that’s a whole ‘nother question!
deleted by creator
I wouldn’t recommend apple os for CAD software. Plus you will get more computer for your money with PCs
If you go linux, I do not recommend System 76. I’ve had two of them and both of them were junk. My company issues linux laptops to developers. 9 out of 10 System 76 laptops failed within a year. I’m not a big fan of Dell. If you have the time and money check out Starlabs. Framework has a lot of promise as well.
If you just need a beater running Windows for browsing and writing, surprisingly, I’ve found HP makes very affordable, reasonably solid machines.
If you want really portable for basic web stuff. I’d suggest an iPad. Lots of VCs and CEO types I know just use iPad.
For CAD you probably want a desktop with a high end mouse and an array of large monitors at an ergonomic desk setup. You’ll probably spend more on the chair and desk and workspace than on the computer.
I love linux, i would recommend it to anyone, just like i recommend people to diy their desktop…. except boomers asking advice on how to get up to date with modern tech. Op needs a prebuild from a good brand.
Thanks for understanding!